ALUMAXOffice & Home Living
Get My Price获取我的价格Dapatkan Harga Saya
Home首页Laman UtamaKitchen / I-Standard

Kitchen · K02

I-Standard Kitchen

Single-wall terrace kitchen — fridge tower, 1.5-bowl sink, integrated dishwasher, hob + hood.排屋单墙厨房——冰箱高柜、1.5槽水槽、嵌入式洗碗机、炉灶＋烟机。

Get My Price获取我的价格Dapatkan Harga Saya WhatsApp this kitchen
I-Standard kitchenSample render

Price rule

From RM11,399

per kitchen · indicative, excl. SST

Confirmed after a Sibu site measurement and an approved drawing. Options below are priced at quotation.

At a glance

Product code
K02
Layout family
I-ShapeI型
Intended zone
Dry干区Kering
Carcass material
E1 plywood
Reference size参考尺寸Saiz rujukan
3.0m wall
Finish level
E1 plywood · Signature

Material & finish

E1 plywood, matched to a dry zone. Colours and finishes are chosen from the ALUMAX finishes library — a screen colour is not final material approval; confirm against a physical sample.

Matte White哑光白Light Oak浅橡木Walnut胡桃木Graphite Grey石墨灰Charcoal炭黑

See the finishes library

Options & upgrades

  • Full-height wall cabinets到顶吊柜 priced at quotation
  • Lift-up flaps上翻门 priced at quotation
  • Built-in microwave嵌入式微波炉 priced at quotation

Included

  • Cabinet supply and the finish level shown
  • Handle system and soft-close hardware
  • Installation under a confirmed scope
  • Warranty documentation保修文件

Excluded unless stated除非注明，否则不含Dikecualikan kecuali dinyatakan

  • Electrical, plumbing and gas
  • Tiling, backsplash and waterproofing
  • Appliances and sink / tap
  • Hacking, demolition and site conditions

Same layout, more kitchen

Compare the range

Same layout family — each step up moves you to a stronger carcass and finish. Prices are the honest 'from' floor; your exact figure follows a free measurement.

K01

I-Compact一字型·紧凑

P6 moisture-resistant board

From RM6,499

per kitchen · excl. SST

See this kitchen
K02You’re viewing

I-Standard一字型·标准

E1 plywood

From RM11,399

per kitchen · excl. SST

K03

I-Grand一字型·豪华

Aluminium honeycomb

From RM21,399

per kitchen · excl. SST

See this kitchen

Product specification

The decisions behind the cabinet

Every cabinet is a set of choices — handle, internal fit-out and the material for its moisture zone. Here is what each option gives you, what it costs you, and where it fits. For why to pick one over another, the decision guides on design.alumax.pro go deeper.

§C Handle & opening type

Knob or surface pull

Usage
Economical, easy to grip and replace.
Visual
Hardware-forward and traditional — a visible knob or pull sits on the door face as a deliberate detail.
Cost
Low
  • Watch Visible; can catch clothing; cleaning around the fixings.
Grip
Easy full-hand grip; good for most users, including limited dexterity.
Projection
Protrudes from the front — can catch clothing or a bag strap in a walkway.
Cleaning
Wipe around the fixing; dust collects at the base.
Child safety
Protruding — pad sharp edges near young children.
Geometry
No effect on internal drawer or door geometry.

Finish code Confirmed at quotation

Edge pull / J-pull

Usage
Cleaner appearance; relatively economical.
Visual
A clean, near-flush line — the grip is the door's own edge, so the front stays largely uninterrupted.
Cost
Low–medium
  • Watch Smaller grip; edge wear; can be difficult for some users.
Grip
Shallow finger grip; harder with limited dexterity or gloves.
Projection
Minimal — the grip is the front edge, so nothing protrudes.
Cleaning
Grease and dust gather along the routed edge.
Child safety
No protrusion; low snag risk.
Geometry
Slightly reduces the usable front face at the pull edge.

Finish code Confirmed at quotation

Gola / C-profile

Usage
Consistent handleless appearance; durable metal interface.
Visual
A fully handleless, continuous horizontal shadow-line across the run — the most architectural, seamless look.
Cost
Medium
  • Watch Requires coordinated modules; consumes some usable space.
Grip
Continuous finger recess; comfortable across the full width.
Projection
None — a recessed rail sits behind the front.
Cleaning
The rail channel collects dust and needs wiping out.
Child safety
No protrusion; safe in traffic routes.
Geometry
Consumes a strip of usable height/width at the gola line; modules must be coordinated.

Finish code Confirmed at quotation

Routed integrated pull

Usage
Seamless visual result.
Visual
A seamless machined pull with no hardware on the face — a quiet, minimal front.
Cost
Medium–high
  • Watch Material limitations; fingerprints and edge wear.
Grip
Shallow; depends on the routed depth.
Projection
None — the pull is machined into the front.
Cleaning
Shows fingerprints; the routed edge wears with use.
Child safety
No protrusion.
Geometry
Only for materials that machine cleanly; slightly reduces the front face.

Finish code Confirmed at quotation

Push-to-open

Usage
Completely clean front.
Visual
A completely flat, handleless front — the purest minimal surface, with nothing to interrupt it.
Cost
Medium
  • Watch Alignment-sensitive; accidental opening; less convenient with wet hands.
Grip
No handle — press to open; awkward with full or wet hands.
Projection
None — a fully flat front.
Cleaning
Fingerprints on the push zone; the mechanism needs occasional service.
Child safety
Children can open it easily; not childproof.
Geometry
Needs a clearance gap and the mechanism behind the front; alignment-sensitive.

Finish code Confirmed at quotation

Motorised / servo opening

Usage
Premium accessibility and large-drawer convenience.
Visual
A flat, handleless front like push-to-open, kept clean by electric opening — minimal with a premium feel.
Cost
High
  • Watch Power, maintenance and replacement cost.
Grip
Touch / servo assisted — best for heavy or high drawers and accessibility.
Projection
None — a flat front with electric opening.
Cleaning
The flat face wipes easily; the drive needs power and service.
Child safety
Powered motion — keep controls out of reach of young children.
Geometry
Needs power, the servo unit and service access behind the run.

Finish code Confirmed at quotation

§D Internal accessories & baskets

AccessoryMain benefitMain limitationCost / value
Adjustable shelfMaximum flexible volume.Poor access at deep lower cabinets.Lowest cost Low
Standard drawerGood visibility and access.Higher hardware cost than doors.Usually high value Medium
Deep pot drawerExcellent kitchen usability.Requires suitable runners and loading design.Medium–high Medium–high
Pull-out pantryAccess to tall, narrow storage.Hardware consumes width; loading and alignment matter.High High
Bottle / spice pull-outUses narrow gaps effectively.Very specialised storage.Medium–high Medium–high
Corner carousel / magic cornerImproves access to blind corners.Expensive; does not recover all corner volume.High High
Dish basketOrganised and ventilated.Drainage, corrosion and cleaning must be considered.Medium Medium
Under-sink organiserUses difficult space.Conflicts with pipes, traps and filters.Medium Medium
Wardrobe liftMakes high hanging space usable.Load and servicing limitations.High High
Trouser / jewellery rackConvenient organisation.Reduces flexible storage.Medium–high Medium–high
Laundry hamperConceals laundry.Ventilation and cleaning needed.Medium Medium

Every accessory is shown open — a closed-door photo can't demonstrate how it works. Open-cabinet photos and usable capacities are added per your configuration.

§F Material by moisture zone

Condition现状KeadaanRequired responseCost
Dry rooms, away from waterP6 or plywood carcass is appropriate.Low
Occasional humidityMoisture-resistant board and protected edges may be suitable.Low–medium
Sink or appliance splash zoneWater-resistant carcass, sealed joints and service access.Medium
Repeated wet cleaningAquaGlass (ACP), honeycomb or appropriate aluminium construction.Medium–high
Possible leaks / floodingRaised or water-stable base, removable access and protected hardware.High
Exterior / extreme exposureFull environmental specification; ordinary cabinetry excluded.Project-specific

Water exposure also affects:

  • Edge banding and seams
  • Plinth material
  • Cabinet back ventilation
  • Sink cut-outs
  • Pipe penetrations
  • Fasteners and basket corrosion
  • Floor-to-cabinet junctions
  • Warranty conditions

Costs are shown as direction (Low → High), not a final figure — your price is confirmed after site measurement and an approved drawing. Decision guides on design.alumax.pro ↗

Questions常见问题

Common questions about this kitchen

How much does the I-Standard kitchen cost?

The I-Standard (K02) starts from RM11,399 per kitchen, indicative and excluding SST. It is a "from" figure — your exact price depends on your run length, layout, material tier, hardware and worktop, confirmed after a free site measurement in Sibu and an approved drawing.

What is the I-Standard kitchen made of?

The carcass is E1 plywood, matched to a dry zone. Moisture-resistant materials resist damp but are not waterproof, so wet and splash zones step up to aluminium, ACP or honeycomb. Colours and finishes are chosen from the ALUMAX finishes library and confirmed against a physical sample.

What is included in the I-Standard price, and what is quoted separately?

Included: the cabinet supply and the finish level shown, the handle system and soft-close hardware, installation under a confirmed scope, and warranty documentation. Quoted separately unless stated: electrical, plumbing and gas; tiling, backsplash and waterproofing; appliances and the sink or tap; and any hacking, demolition or site conditions.

How do I get an exact quote for my kitchen?

Send your room size and preferred finish level and we prepare an indicative range, then confirm the material, handle and scope after a free site measurement in Sibu and an approved drawing.

Design concepts · ELS Studio

See the kitchen look before you commit

Approved kitchen design renders from the ELS Studio library — concept studies of the style and layout, not photos of this exact kitchen. Your cabinetry is produced to your approved specification. ELS designs and specifies; ALUMAX supplies and installs.

Kitchen design concept — Warm Wood Modern style
Design renderWarm Wood Modern
Kitchen design concept — Scandinavian style
Design renderScandinavian
Kitchen design concept — Scandinavian style
Design renderScandinavian
Kitchen design concept — Scandinavian style
Design renderScandinavian
Kitchen design concept — Warm Wood Modern style
Design renderWarm Wood Modern
Kitchen design concept — Warm Wood Modern style
Design renderWarm Wood Modern

These are ELS Studio concept studies — the finished cabinetry is produced to your approved specification and will vary with your space, materials and finishes. Explore ELS Studio ↗

Which layout & material — decide on design.alumax.pro Design & coordinate the whole room — ELS

Save this kitchen

Leave your WhatsApp and we’ll prepare an indicative range for the I-Standard within 1 working day. No obligation.

Ready for a number?

Get your kitchen budget in two minutes.

Send your room size and finish level — we confirm material, handle and scope after a free Sibu measurement.

Get My Price获取我的价格Dapatkan Harga Saya WhatsApp ALUMAXWhatsApp 联系 ALUMAX

All kitchen layoutsBuild your own kitchen

Get My Price获取我的价格Dapatkan Harga Saya